6 Port 100Mbps PoE Switch

<< Click to Display Table of Contents >>

Navigation:  »No topics above this level«

6 Port 100Mbps PoE Switch

 

POE304 - Quick Start Guide

 

POE304

 

 

POE304-QRCODE

www.systemq.com/PDF

/manual/xPOE304.pdf

 

 

A PoE switch is a network switch which has power over Ethernet built-in.

 

The PoE switch will detect whether the load device is PoE compatible and provide PoE power automatically and network connection.

 

The units add extra flexibility to a network infrastructure thanks to 100 metre run capabilities both in and out of them.

User Information

The PoE Switch must be installed in a clean, dry environment where it will not be exposed to high temperatures, moisture or excessive dust.

Do not touch the PoE Switch or any of its connections with wet hands.

Ensure the power is switched off if the PoE Switch is not in use for a long period of time.

There are no user serviceable parts in the PoE Switch and opening or attempting to repair the product will void the warranty.

Only use the PSU originally supplied with the product.

Do not install or use the device if the power cable is damaged.

 

The Switches have different uses and setup options. Including providing power to PoE Cameras, and providing network access to devices like computers.

 

Setup Options

Option 1

To power IP Cameras using the PoE switch then connect the IP Cameras using CAT5e/CAT6 Ethernet Cable, for longer distances we recommend using high quality cable, with solid copper cores.

POE-Option1

 

 

Option 2

Provide network infrastructure to PoE and non-PoE Devices, like computers, and other Network devices..

POE-Option2

 

LED Status Indicators

LED

Condition

Status

Power

POWERLED1 On

The switch is receiving power

PowerLEDoff Off

The switch is not receiving power

Network / Link

PoELED On

The port is connected

LEDoff Off

No connection to the port

PoELED LEDoff Flashing

The port is transmitting or receiving data

 

 

VLAN

The VLAN switch allows separation between ports. As default VLAN is off, when VLAN is on ports on the different blocks won’t be able to see each other. Note that the UPLINK does see all ports so the separation is only between ports.

 

Troubleshooting

Problem

Possible Cause

Solution

No Power light on Switch

No power to the device

Check power to device from external source. Check that the power lead (IEC lead) is plugged in to the PSU and the PSU is plugged into the switch.

Loose connection

Check that the power lead (IEC lead) is plugged in to the PSU and the PSU is plugged into the switch.

Network light not flashing

Poor quality cable or termination

Check the Ethernet cabling to your device is of good quality and is terminated correctly.

Connected devices not powering

Poor quality cable or termination

Check the Ethernet cabling to your device is of good quality and is terminated correctly

Total power consumption exceeded

Check the load devices are not above the total power consumption of the switch.

Cable length

Check the distance of Ethernet cable to your device. Ethernet cables have a 100m maximum length.

Slow flashing LEDs, No network on load devices

Faulty cable or device

Turn the power off to the switch & unplug the load devices (Check Ethernet cabling to load devices). Leave the switch turned off for 10 seconds and then power the switch back up, plug each device back into switch individually to help troubleshoot the suspect cable.

 

Specification

Downlinks

4 x RJ45

Uplinks

2 x RJ45

PoE

30W (Max per port)

Power

96W (Whole device maximum)

Bandwidth

10Mbps / 100Mbp

Use

Internal Use Only

Working Temperature

0°C ~ 40°C

Power Input

240V AC (Lead supplied)

Dimensions

(w)210 x (d)136 x (h)44.5mm